How to Install a Hydraulic Throwout Bearing

How to Install a Hydraulic Throwout Bearing

The Way to Not Make the Same Mistakes Everyone Else Does

Incorrectly aligning the mounting bracket is a common problem when installing a hydraulic throwout bearing.

The ideal angle for the mounting bracket is between 3 and 9 o’clock, with the bottom of the bracket never facing down.

A bleed line must be attached to the top fitting.

By forcing fluid into the bearing, a bleed eliminates the possibility of air bubbles.

If you’ve followed the instructions up until this point, installing the hydraulic throwout bearing shouldn’t be too difficult.

In the first step of the installation process, the distance between the clutch fingers and the hydraulic throwout bearing must be measured.

One-eighth of an inch is the most space that can exist between the two parts (sixteenth of an inch).

Too narrow of a space prevents the clutch from being fully released and can lead to premature wear on the clutch fingers.

The clutch will slip during the bleeding cycle as well.How to Install a Hydraulic Throwout Bearing

Another frequent mistake is neglecting to release one’s foot from the clutch after shifting gears.

This causes the clutch pedal to become stuck and difficult to release. An Instructional Guide for Mounting a Hydraulic Throwout Bearing.

It’s likely that a worn out throwout bearing is to blame for a clutch pedal that’s difficult to depress.

Any of the clutch release bearing, collar, or quill could be harmed by a defective throwout bearing.

If you don’t get the clutch release bearing fixed, your car will have issues.

line topped with a bleeder valve.How to Install a Hydraulic Throwout Bearing

Install the bleeder valve, swivel fittings, release bearing, and adjustment screw into the hydraulic throwout bearing assembly.

The transmission’s input shaft must be parallel to the heavy string’s length so that it can be fed through the bell housing opening.

Make sure the transmission is properly seated in the bell housing and swivel nut before inserting the line.

Make sure the line doesn’t touch anything that might start it spinning, such the flywheel or the clutch.How to Install a Hydraulic Throwout Bearing

For information on how to properly install an AN bleeder valve, please refer to the manual supplied by the valve’s manufacturer.

A bleeder valve line should be added if one is not already present.

Ensure that the bleeder valve is accessible to the master cylinder.

After the new brakes have been installed, the master cylinder should be refilled with brake fluid of type 3 or higher.

It is not advised to use synthetic brake fluid since it can harm o-rings and render your warranty null and void.

Verify that the safety hose is in position and securely fastened after bleeding the system with the AN bleeder valve.

Since brake fluid and hydraulic fluid can corrode paint, you should eliminate any remaining check valves.How to Install a Hydraulic Throwout Bearing

The bleeder valve on the top of the hydraulic throwout bearing should provide a snug fit for the line.

A Guide to Mounting a Hydraulic Throwout Bearing

Separation is necessary.

To ensure a smooth hydraulic throwout bearing assembly, a master cylinder with a 3/4-inch bore is necessary.

This hydraulic throwout bearing arrangement necessitates the use of a master cylinder with a 3/4-inch bore.

To get rid of the old throwout bearing, remove the pilot tube from the input shaft bearing retainer.

The gearbox’s bearing retainer should then be removed.

The bearing must then be installed according the manufacturer’s specifications. Before putting in the hydraulic throwout bearing, make sure you read the assembly’s instructions. Time zones should be separated by no more than nine hours.How to Install a Hydraulic Throwout Bearing

A bleed line must be attached to the top fitting.

When fluid is pumped through the bleed line, it pushes any air bubbles out of the bearing.

As a last step, attach the remaining fitting to the bleed line.

If everything went according to plan during installation, you shouldn’t have to touch the screws. A measurement taken between the bell and the block will reveal the correct separation.

A Guide to Mounting a Hydraulic Throwout Bearing

After all is said and done, the bearing face location should be four millimeters less than the first reading.How to Install a Hydraulic Throwout Bearing

Having too much space between them can cause the clutch or bearing to slip.

The bearing seal could break down and fluid could escape if the clearances are too tiny.

Ensure the bearing is perfectly level before attempting to alter the gap.

A hydraulic throwout bearing requires precise clearance between the master cylinder and the bearing itself during installation.

Forcing the throwout bearing to travel too long before it collides with the clutch fingers can prevent the clutch from being released.

This could make shifting and stopping more challenging.

A successful installation requires precise gap measuring.

After ensuring the suitable spacing, install the bearing.

Tutorial on Setting Up a Hydraulic Throwout Bearing

When setting up this bearing, the hydraulic release bearing set-up tool from removes any element of doubt.

It is unnecessary to pry the transmission from the bellhousing because the set-up tool fastens the hydraulic release bearing and pressure plate fingers. A Guide to Mounting a Hydraulic Throwout Bearing

The clearance of the hydraulic throwout bearing can also be adjusted with its help.

The set-up tool will help you keep the hydraulic release bearing in the correct position once you’ve installed the bearing.

Locating the master cylinder’s bore and stroke is a prerequisite to installing a hydraulic throwout bearing.How to Install a Hydraulic Throwout Bearing

A master cylinder with a 3/4″ bore is needed for this bearing.

Use the fuel line as a makeshift hose if necessary.

It is necessary to determine the best path for the hydraulic line that will lead from the far-off reservoir to the clutch master control.

When putting in a slip-on bearing, you’ll need a depth tool, which can be purchased from any of the normal outlets.

A Guide to Mounting a Hydraulic Throwout Bearing

It helps maintain the correct distance between the bearing and the transmission/clutch fingers up front.

This bearing set is meant to be used with based transmissions and allows for the release of the hydraulic clutch.How to Install a Hydraulic Throwout Bearing

For proper installation, the original transmission bearing retention bolt must be removed and the provided stud must be inserted into the corresponding hole.

After that, slide the tool over the shaft to lock it in place.

The bearing retainer shaft cannot spin since the tool slides smoothly along it.

Shims are shown for demonstration reasons only and must be adjusted for a suitable bearing fit.

To ensure the security and functionality of your vehicle, you need a top-notch hydraulic throwout bearing.

The shaft of a hydraulic throwout bearing uses hard-anode billet aluminum.

The hydraulic throwout bearing is held together with bolts and high-pressure stainless steel braided lines.How to Install a Hydraulic Throwout Bearing

Next, the shaft is forced onto the diaphragm spring’s center, which separates the pressure plate and clutch disc.